UltraScape Flowpoint Fine

Rapid set fine grout with high fluid consistency. Ideal for natural stone, concrete flags, porcelain tiles and clay paviours.

• Pack Size: 20 kg bucket

• Colours: Natural Grey & Charcoal

• Yield: Approximately 11.12 m² per 20 kg bucket

--

UltraScape Flowpoint Fine: Super Fine Flowable Grout

UltraScape Flowpoint Fine is a rapid set grout with high fluid consistency. Ideal for natural stone, concrete flags, porcelain tiles and clay paviours.

• Pack Size: 20 kg bucket

• Colours: Natural Grey & Charcoal

• Yield: Approximately 11.12 m² per 20 kg bucket

For bulk orders please contact us on 01933 426225 for the best deals available. Large local stock at multiple U.K. branches, with collection by appointment welcomed. To locate your nearest branch please click here.

To view our pallet prices please click here.

Product Description

UltraScape Flowpoint Fine is a rapid set grout with high fluid consistency for early trafficking that conforms to the strict demands of BS 7533. It is ideal for all paving areas where a rigid or bound void-free joint is required. The product is suitable for application on driveways, patios, town centre pedestrian schemes, pathways and carriageways. The product can be used with natural stone, concrete flags, porcelain tiles and clay paviours.

Product Advantages

• Joint widths: 2-50 mm

• Open to foot traffic: 1 hour

• Open to vehicular traffic: 4 hours

• Just add water

• Set time: 15 minutes at 20°C

• BS 7533 compliant

• For use with all types of paving elements

Information Video

Brochure

To download the UltraScape Compliant Paving System brochure please click here.

Supporting Products

• Ultrascape Eco-Bed – bedding material

• Ultrascape Pro-Prime Slurry Primer – provides an exceptional bond between your paving and bedding mortar

Technical Information

Flowpoint Fine is a fully pre-mixed dry-pack which only requires tile addition of water on-site. It can fill joints from 2 mm to 50 mm wide with a minimum target depth of 20 mm, up to 200 mm In one application. This highly fluid grout achieves a final compressive strength of 49.6 N/mm² (results achieved using 3.4 litres of water per 20 kg bucket), and will reach initial set in 30 minutes, will accept light foot traffic after 1 hour, and vehicular traffic after 4 hours (dependent upon temperature).

Mixing and Application

Once the paving is ready to receive the grout the following method must be adhered to:

• Immediately prior to jointing it must be ensured that the joints are free from debris and all ponded water removed

• The paving surface and joints must be pre-soaked and kept wet until the jointing process has been completed

• A 20 kg bucket requires 3.4 litres of water and must be mixed for between 3 and 5 minutes until a smooth lump-free consistency has been achieved

• Apply the mortar without delay. Do not store liquid mortar other than in transit from mixer

• Mortar must be carefully forced into the joints using a suitable rubber squeegee

• The mortar should be constantly moved over the surface to repeatedly top up joints in which the mortar may have slumped following initial placement

• Use the rubber squeegee to remove as much mortar as possible from the surface

• The surface must be kept constantly moist using a soft spray of water

• When the jointing mortar has hardened sufficiently or achieved its initial set the paving surface must be cleaned using a brush and copious amounts of water

• Cleaning must be carried out thoroughly and no mortar must be allowed to remain on the surface of the paving

Workability is approximately 5-15 minutes depending on temperature.

Precautions

• Wash all tools frequently

• Mix only enough material to apply in 4 minutes

• Never remix or add extra water

• Wear protective clothing

• Cool temperatures retard, warm temperatures accelerate

• Care should be taken when using the product near drainage. You will need to make sure you have a run-off to take the excess away as it cannot go down a drain

Please note: a small trial should be done to ensure compatibility with the stone being used as it is impossible to test all stone types.

Safety

• Please ensure that appropriate PPE is used when preparing, mixing and applying products

• Always wash hands before consuming food and make sure that materials are kept safely out of reach of children and animals

• Avoid skin and eye contact - wet cement can burn the skin

• Please dispose of packaging and waste responsibly and in accordance with local authority requirements

• A full material safety data sheet relating to this product is available - please contact us to request a copy

Contact Us

For further advice regarding the use of this product, technical support or a quotation please contact us.