NATCEM AC

A blend of potable water approved natural cement based binder, specially dried and graded aggregates and food grade retarders. It is designed for a
thickness application from 3 mm up to 20 mm to produce a fair-faced finish to concrete or masonry surfaces.

--

 

NATCEM AC

NATCEM AC is a blend of potable water approved natural cement based binder, specially dried and graded aggregates and food grade retarders. It is designed for a
thickness application from 3 mm up to 20 mm to produce a fair-faced finish to concrete or masonry surfaces.

• Approved to Reg. 31 for use in public water supplies. Secretary of state for D.E.T.R. Approved

• Yield: Generally, 1 x 25 kg bag of NATCEM AC mixed with 5 litres of water will produce approximately 10 litres of finish mortar

• Pricing: Please contact us for a free quotation

 

Product Description

NATCEM AC is based on a Natural Cement based binder and an anti-carbonation coating that can also be used as a concrete repair mortar. It is an environmentally friendly, fast setting, high early strength concrete repair material that starts to set in 35 minutes.

The product only requires to be added to water and mixed for 2 minutes (see mixing instructions for further details), and unlike most other manufacturers products does not require primers, bonding agents and or curing agents. It can be used in cold & wet conditions, sets under water and from a minimum of 3 mm can be, if required, built up layer on layer to any thickness. It is also Reg.31 approved for contact with drinking water with only ½ hour curing period after set required.

 

Recommended Uses

• Chemical Resistance

• Reg.31 Approved Products for contact with drinking water

• Concrete Repairs

• Tanking

• Grouting

• Rendering

• Floor Screed

• Anti-carbonation coating

• Concrete repair

• Infill surface imperfection

• Void filling

 

Sectors

• Utilities

• Construction

• Civil Engineering

• Railways

• Sea Defense

• Water

 

Product Advantages

• Tested to BS 6920:200 Effect on Water Quality

• Approved to Reg. 31 for use in public water supplies

• Easy to apply using brush, roller or trowel

• Wide range of application thickness

• Low permeability provides protection against water-borne chlorides

• Excellent adhesion to concrete and masonry

• Low shrinkage

• Can be applied to wet and cold surfaces

• No curing compound necessary

• Sets down to zero

• For use in contact with potable water

• Can be used underwater

• Adheres to wet & green concrete

• Fast Curing ½ hour only after set

• Fast Setting

• No need to grit blast steel reinforcement

 

 

Natural Cement Product Range

NATCEM 35	NATCEM AC	NATCEM D	NATCEM DW
NATCEM Tank	NATSEAL	Grout 105	CWG Grout
LUL RapideSet	ShotCrete AS90	ShotCrete 430F	ShotCrete 437F
ShotCrete 513	ShotCrete 530	TrackCrete	WaterStop

 

Related Product Videos

The following videos feature NATCEM 35 - please refer to the product data sheet for full instructions regarding the use of NATCEM AC.

 

Surface Preparation

Please refer to the product data sheet or contact us for advice.

 

Mixing

Please refer to the product data sheet or contact us for advice.

 

Application

Please refer to the product data sheet or contact us for advice.

 

Cleanup

NATCEM AC should be removed from tools and equipment with water immediately after use.

 

Storage

NATCEM AC is packaged in a polythene inner bag with a resealable tie within a stitch sealed woven polypropylene outer bag, which should be stored in dry conditions and will last for at least twelve months.

 

Precautions

We strongly recommend the use of gloves, goggles and mask. Please see the product safety data sheet or contact us for full details.

 

Contact Us

For further advice regarding the use of this product, technical support or a quotation please contact us.